Skip to content
EN
DIY & Home Repairs

How to Regrout Tile: Remove Old Grout and Redo It

Learn how to regrout tile: scrape out old grout, mix and pack new grout, wipe the haze, and seal it. Plus common mistakes and when to call a pro.

Yeşil Köşe Editörü · · 4 min read

Gray square ceramic tiles with light grout lines forming a clean grid pattern.

To regrout tile, scrape out the old grout to about two-thirds of its depth, vacuum the joints clean, mix fresh grout to a thick peanut-butter consistency, press it into the gaps with a rubber float, and wipe the surface with a damp sponge. Let it cure, then seal it. A small bathroom wall is a weekend job. A whole floor takes longer, mostly because of the scraping.

Here is the order that works.

  1. Put on safety glasses and a dust mask. Old grout throws fine dust, and some of it will be silica.
  2. Run a grout saw or carbide scraper along each joint. Keep it steady and don't let it skate onto the tile edge. Aim for a depth of roughly 1/8 to 1/4 inch (3–6 mm), or about two-thirds of the way down.
  3. Vacuum every joint, then wipe with a barely damp cloth. Any dust left behind weakens the bond.
  4. Mix only what you can use in about 20–30 minutes. Powder grout should be slightly stiffer than you think it needs to be. Follow the bag for the water ratio.
  5. Hold the float at roughly a 45-degree angle and push grout diagonally across the joints, so it packs in rather than just sitting on top. Go over each joint twice.
  6. Scrape off the excess with the float edge, then wait 15–30 minutes. Wipe with a well-wrung sponge in light, circular passes. Rinse the sponge often.
  7. Buff away the leftover haze with a dry cloth after a few hours. Keep the area dry for 24–72 hours, depending on the product, and seal cementitious grout after the cure time on the label.

Choose the right grout first

Use unsanded grout for joints narrower than about 1/8 inch (3 mm), and sanded grout for wider ones. Sanded grout resists shrinking and cracking in wide gaps. Unsanded grout can scratch soft stone, so check before you use sanded on marble or polished surfaces. A hardware store or garden center shop floor won't help much here. Tile shops and larger home improvement stores carry both types.

Weathered green square ceramic tiles set in a wall with light, uneven grout lines between them.
Grout color and width change how a tiled wall looks, so pick yours first. · Photo: MabelAmber / Pixabay

If the tile is in a shower, look for a grout labeled for wet areas. Premixed and epoxy options exist too. They are easier to work with but can be tougher to clean up, so read the label before you buy.

Mistakes that ruin a regrout

The biggest one is a shallow removal. If you only scratch the surface, the new grout has nothing to grip and will crumble or lift within months. Dig deeper than feels necessary.

Pile of broken white ceramic tile pieces with orange edges and mortar residue.
Careless scraping or prying can crack tiles and add to your repair work. · Photo: Nannica / Pixabay

The second is too much water, either in the mix or on the sponge. Soupy grout shrinks as it dries and leaves pits. A sponge that is dripping can pull grout straight out of the joints and wash out the color, which leaves patchy lines.

The third is clean-up timing. Wipe too early and you smear grout all over. Wait too long and it sets like cement on the tile face. Test a small spot first, especially in a warm, dry room where grout firms up fast. In humid coastal homes it can take noticeably longer.

If mold is the reason you're regrouting, clean the area first. Never mix bleach with ammonia, vinegar, or any acidic cleaner, because it makes toxic gas. Ventilate the room and wear gloves. The same rule applies to any cleaning product you use around your washing machine, and the washing machine cleaner guide covers safe choices there.

When to worry

Grout cracks are usually cosmetic. But if the tiles themselves are loose, hollow-sounding when you tap them, or the cracks run in a line across the floor, the problem is underneath. Regrouting won't fix that.

Soft, crumbly walls behind a shower, a musty smell that returns, or tiles that move under your hand all point to water getting behind the surface. At that stage you may need to remove tile and check the backing. Call a tile pro or a contractor before sealing in a bigger problem.

One last practical tip: take a clear photo of your current grout color in daylight before you shop. Dry grout looks lighter than wet grout, so buy a little extra and test in a corner.

Comments

Loading comments…

Related articles