Washing Machine Cleaner: Which Kind to Use and How
Not sure which washing machine cleaner to use? Compare vinegar, baking soda, bleach and tablets, then follow a simple step-by-step clean that actually works.

The best washing machine cleaner is the one that matches your problem. For a musty smell and general gunk, a hot cycle with a cup of white vinegar works well in most machines. For black mold on the door seal, bleach (diluted, and used on its own) does the job. Commercial cleaning tablets are fine too, if you'd rather not measure anything. Just never combine any of these in the same wash.
That last point matters more than anything else here, so here it is up front.
What you need
Grab white vinegar (about 2 cups, or 480 ml), baking soda (half a cup, or 120 g), a few microfiber cloths, and an old toothbrush. If you have black mold, add household bleach, rubber gloves and a window or fan for ventilation. Cleaning tablets from the supermarket or hardware store are an alternative to all of the above. Check your manual first, because some makers advise against vinegar on rubber seals over the long term, and some front loaders have a dedicated cleaning cycle you should use instead.

Cleaning the machine step by step
- Empty the drum completely. Check for stray socks tucked behind the door seal.
- Pull out the detergent drawer. Soak it in warm soapy water while you do everything else. Many drawers lift out after pressing a release tab, but check yours before you force it.
- Scrub the empty drawer slot with the old toothbrush. Mold likes to hide at the back of that cavity, so shine a flashlight in there.
- Pull back the rubber door seal on a front loader and wipe all the way around inside the folds. Use a cloth dampened with warm water and a little vinegar. For stubborn black spots, use a diluted bleach solution instead (follow the label on your bleach, and do not use vinegar anywhere in the same session). Wear gloves and open a window.
- Pour 2 cups (480 ml) of white vinegar straight into the drum. Skip this step if you used bleach on the seal. Start with the vinegar day, bleach on another.
- Run the hottest, longest cycle your machine has, ideally 140°F (60°C) or higher, with nothing inside. Many machines have a tub-clean or sanitize setting that does this.
- When it finishes, sprinkle half a cup (120 g) of baking soda into the drum and run a second short hot cycle. This helps lift leftover residue and odor.
- Wipe the drum, the seal and the door glass dry. Put the drawer back in.
- Leave the door and drawer open so the inside can dry out.

If you'd prefer a tablet, skip the vinegar and baking soda. Drop one in the empty drum, run the hot cycle and follow the packet instructions, which differ between brands.
Which cleaner for which problem
Vinegar is best for light smells and mineral scale, especially if you live in a hard water area. It's cheap and easy to find in any grocery store. It's less useful against heavy mold.

Bleach is the one for visible black mold on seals and in the drawer slot. It's strong, so ventilate and keep it off colored plastic parts where possible.
Baking soda is mild. Use it as a deodorizer, not as a mold killer.
Tablets are convenient and consistent, and they suit people who run lots of cold washes where residue builds up fastest. They cost more over time than vinegar.
Climate matters a little. In humid coastal areas the seal and drawer grow mold faster, so you'll clean more often. In a dry southern climate, scale is usually the bigger issue. In cold regions where you wash on cold cycles all winter, soap residue and bacteria can build up, so a monthly hot cycle makes a visible difference.
Where it usually goes wrong
The biggest mistake is mixing products. Someone runs vinegar, sees no improvement, then adds bleach in the same cycle. Don't. Pick one, finish the cycle, and wait a day if you want to try another.
Second, people clean the drum and ignore the seal and drawer. That's where the smell is coming from most of the time. A spotless drum with a moldy gasket will still make your laundry smell.
Third, using too much detergent. Extra suds don't mean cleaner clothes. They leave a film that feeds mold. If you use high-efficiency (HE) detergent in an HE machine, a couple of tablespoons is often enough, but follow the bottle.
Fourth, shutting the door right after the last load. A damp, sealed drum is a mold incubator. Leave the door ajar.
If the smell returns within a week or two of a thorough clean, check the drain filter. On many machines it sits behind a small panel at the bottom front. Place a shallow tray and towels underneath, because water will come out. Clear out coins, lint and hair. A clogged filter or drain hose can keep standing water in the machine, and no cleaner fixes that.
Keeping it fresh
Run a hot cleaning cycle about once a month, more often if the machine is in a humid bathroom or basement. Wipe the seal after heavy loads. Pull the drawer every few weeks and rinse it. Take wet towels and gym clothes out promptly instead of letting them sit.

If you're doing this on a weekend in a warm place, the same vinegar you buy for the machine also works on windows and mineral spots on glass. Handy, but keep it far from the bleach shelf.
Comments
Loading comments…


